Pump-solutions-group Neptune Polymaster Liquid Polymer Blend & Feed Manual do Utilizador

ZL107874 Revised 12-8-2009 IINNSSTTAALLLLAATTIIOONN,, OOPPEERRAATTIIOONN AANNDD MMAAIINNTTEENNAA

5 REMOTELOCALOFFFAULT ONCHEMICAL PUMP CO., INC.PolymasterCHEMICAL PUMP CO., INC.ONFAULTREMOTELOCALOFF TYPICAL FRONT PANEL WITH ELECT

6 OPERATING INSTRUCTIONS Please refer to system specific mechanical and electrical drawings and schematics for full information about the particular

7 DILUTION WATER FLOW CONTROL 1. The flowmeter indicates the dilution water flow rate. The water flowing through the flowmeter does not contain any

8 LONG TERM STORAGE INSTRUCTIONS If the system will not be operating for an extended period of time, all the polymer should be purged from the syste

9 START-UP 1. Apply power to the unit by turning the switch at the top right of the unit to “LOCAL”. The red “ON” light should come on. Since water

10

11 CALIBRATION 1. Calibration of the polymer pump is recommended once the system is operational. Differences in the specific gravity and viscosity o

12 CALIBRATION GRAPH For your convenience, the vertical scales on this graph are labeled for English Units (gallons per hour) or Metric Units (millil

13 INSTRUCTIONS FOR OPERATION OF POST-DILUTION UNIT (Applies to 2 stage dilution furnished on models PA/PM-3000 and PA/PM-3000R only) The models P

14

WARNING LOCKOUTS ARE REQUIRED BEFORE SERVICING THIS EQUIPMENT. SAFETY INSTRUCTIONS: Shut off/Lockout pump Power be

15 MAINTENANCE 1. Inspect for polymer or water leakage at the components. A. If joint leakage is observed, tighten carefully. Most joints are plast

16 Polymaster®P.O. Box 247 Lansdale Pa. 19446Phone 215-699-8700 Fax 800-255-4017Pression D'eauMaximumTempératureMaximaleP/N 107807www.neptune1.co

17 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Pump running but not pumping chemical. Air leak in suction line. Tighten hosing and clamps.

18

19 WARNING! Warranty void if "Y"strainer notinstalled on inlet lineWARNING! Warranty void if "Y"strainer notinstalled on inlet lin

20 REMOTELOCALOFFFAULT ONCHEMICAL PUMP CO., INC.PolymasterWARNING! Warranty void if "Y"strainer notinstalled on inlet lineWARNING! Warranty

21 REMOTELOCALOFFFAULTONCHEMICAL PUMP CO., INC.PolymasterWARNING! Warranty void if "Y"strainer notinstalled on inlet lineWARNING! Warranty v

22 REMOTELOCALOFFFAULT ONCHEMICAL PUMP CO., INC.PolymasterWARNING! Warranty void if "Y"strainer notinstalled on inlet lineWARNING! Warranty

23

24

WARNING Please read thoroughly before installation, operation or maintenance of any Polymaster Machine EQUIPMENT MISUSE HAZARD Equipment misuse ca

25 WARNING! Warranty void if "Y"strainer notinstalled on inlet lineWARNING! Warranty void if "Y"strainer notinstalled on inlet lin

26 WARNING! Warranty void if "Y"strainer notinstalled on inlet lineCHEMICAL PUMP CO. , INC.ONFAULTREMOTELOCALOFF"ATTENTION! Cet équipe

27 1LL32/@0$67(5

28 1LL32/@0$67(5

29 Polymaster MAINTENANCE LOG Spare Parts Kit #__________________________ NEPTUNE CHEMICAL PUMP CO., INC. Tel.: 215-699-8700 • FAX: 215-699-037

Polymaster ™ TABLE OF CONTENTS PAGE NO. INSTALLATION 2 CAUTION! 3 THEORY OF OPERATION 4 OPERATING INSTRUCTIONS 6 LONG TERM STOR

NEPTUNE CHEMICAL PUMP COMPANY LIMITED WARRANTY All Neptune Polymaster units are tested at the factory prior to shipment. Each part used in their co

1 TYPICAL BACK PANEL WARNING! Warranty void if "Y"strainer notinstalled on inlet lineWARNING! Warranty void if "Y"strainer notin

2 INSTALLATION 1. Unpack Polymaster from shipping container. Inspect system for any shipping damage and report it to the freight company and to Ne

3 CAUTION In addition to this instruction, there is a project specific mechanical drawings, a project specific electrical drawing and a metering pum

4 THEORY OF OPERATION The Neptune Polymaster polymer dilution system has three basic subsystems which are the water and Polymer feed/metering subsyst